RVM90-4Products > BENDING SOLUTIONS > Rolla-V > RVM90-4_12.7RVM90-4_13

RVM90-4_12.7

Article No. Model Length Weight Price
RVM90-4.250.12,7 offset tang 250 mm 23,3
RVM90-4.500.12,7 offset tang 500 mm 58,1
RVM90-4/SP.12,7 Spring
RVM90-4/IN.12,7 Insert
RVM90-4/DO.12,7 Dowel
RVM90-4/U.12,7 U Clip
Rolla-V die with milled groove 12.7 x 19 mm. RVM series in 42 Cr. max.load 3000 kN/m. min. angle 73°
Rolla-V die with milled groove 12.7 x 19 mm. RVM series in 42 Cr. max.load 3000 kN/m. min. angle 73°
  • Description
  • Features
  • Attachments

Rolla-V die with milled groove 12.7 x 19 mm. RVM series in 42 Cr. Max.load 3000 kN/m. Minimum angle 73°.

The Rolla V dies are distinguished from the traditional ones by the presence of 2 oscillating rotors which support the sheet metal before the bending process. Their peculiarity consists in the rotation of the rotors that accompanies the sheet metal during the bending with a drastic reduction of the friction resistance and of the length of the minimum edge. This type of tool applies the concept of tangential bending whereby the behavior of the sheet is different: this is more noticeable if holes and slots are present near the bending areas. Thanks to this concept, these areas do not undergo the classic deformations more commonly known as "slurries".

  • Sheet metal supported during bending process
  • Minimum movement of the sheet metal on the inserts reduces bending marks
  • Internal bending radius is the same of the punch tip radius

HANDLES INCLUDED

In order to facilitate the movement of RVM, RVPV3 and RVHD series, it's possible to mount  specific handles for manual lifting (where the weight permits) or mechanically operated through threaded holes. Thanks to this solution, positioning and removing the die from the press brake is an easy and safe operation.

Sheet metal thickness 6,0 mm/0,236 in 8,0 mm/0,314 in 12,0 mm/0,472 in
with "V" 85 mm/3.346 in 85 mm/3.346 in 85 mm/3.346 in
Max. Load kN/m 3000 3000 3000
Min. Angle 78° 76° 73°
Necessary Strength - Mild steel* 260 500 1290
Necessary Strength - Stainless steel** 440 840 2150
Min. External edge  56.6 mm/2.188 in 56.6 mm/2.188 in 56.6 mm/2.188 in
Max. external radius 36.4 mm/1.433 in 36.4 mm/1.433 in 36.4 mm/1.433 in

*Necessary Strenght - Mild steel max.450 N/mm2

**Necessary Strenght - Stainless steel max.700 N/mm2

ACCESSORIES

RVX1: GREASE

RVX1 grease is a lithium lubricant with particular properties. Thanks to its additives it bears the loads of compression. It protects the parts subjected to sliding. Very suitable for preserving the seat of the inserts or rotors and avoiding abrasion. The single pack contains 500 g of grease.

Add to cart

RVX-TAPE: PROTECTION

Fix the RVX-TAPE protections on the dies for those applications where the sheet metal must not show any signs. These are adhesive strips made with composite materials able to resist compression and to maintain a particularly compressible and anti-friction contact surface with the sheet.

Add to cart

RV-TO: ASSEMBLY TOOL

This tool is created to facilitate the release of the spring from its lower pin. Thanks to its shape, the tool allows you to start the operation in absolute safety and to replace worn parts very quickly.

Add to cart

RVHD2.5

Adjustable "V" Rolla-v die in 42 Cr. Max.load 2500 kN/m. Minimum "V" 28 mm. Maximum "V" 69 mm.

RVHD2.5_12.7

Adjustable "V" Rolla-v die with 12.7mm tang in 42 Cr. Max.load 2500 kN/m. Minimum "V" 28 mm. Maximum "V" 69 mm.

RVHD2.5_13

Adjustable "V" Rolla-v die with 13mm tang in 42 Cr. Max.load 2500 kN/m. Minimum "V" 28 mm. Maximum "V" 69 mm.

RVHD2.5_60

Adjustable "V" Rolla-v die with 60mm base in 42 Cr. Max.load 2500 kN/m. Minimum "V" 28 mm. Maximum "V" 69 mm.

RVM70-3

Rolla-V die with milled groove 13 RVM series in 42 Cr. Max.load 2500 kN/m. Minimum angle 47°.

RVM70-3_60

Rolla-V die with 60 mm base. RVM series in 42 Cr. Max.load 2500 kN/m. Minimum angle 47°.

RVM70-3_90

Rolla-V die with 90 mm base. RVM series in 42 Cr. Max.load 2500 kN/m. Minimum angle 47°.

RVM2.5

Rolla-V die with milled groove 12,7 x 19 mm. RVM series in 42 Cr. Max.load 2000 kN/m. Minimum angle 46°.

RVM2.5_12.7

Rolla-V die with milled groove 12,7 x 19 mm. RVM series in 42 Cr. Max.load 2000 kN/m. Minimum angle 46°.

RVM70-3_12.7

Rolla-V die with 12.7mm milled groove. RVM series in 42 Cr. Max.load 2500 kN/m. Minimum angle 47°.

RVM70-3_13

Rolla-V die with milled groove 13 RVM series in 42 Cr. Max.load 2500 kN/m. Minimum angle 47°.